Toro 23898 Original Instructions Manual Download Page 1

Page: 1 / 24

Form No. 3429-304 Rev A

4050 Directional Drill

Software Versions A–D

Model No. 23898—Serial No. 316000001 and Up

Model No. 23899—Serial No. 316000001 and Up

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

Visit www.Toro.com for product safety and operation
training materials, accessory information, help finding
a dealer, or to register your product.

Joysticks

4-Button Joysticks

g290345

Figure 1

8 or 9-Button Joysticks

g290344

Figure 2

Main Information Screen

This is the first screen that appears after the initial
splash screen. To navigate between screens, use the
left and right arrows.

g287717

Figure 3

Drill speed (rpm)

Engine speed (rpm)

Rotary torque

Drilling-fluid flow rate

Thrust force

Drilling-fluid / Air-hammer
pressure

Original Instructions (EN)

Printed in the USA

*3429-304* A

Summary of Contents for 23898

























Search results

Summary of Contents for 23898

Reviews:

Related manuals for 23898

Brands by name

Popular brands

Toro 23898, Original Instructions Manual

Search results

Summary of Contents for 23898

Reviews:

Related manuals for 23898

Brands by name

Popular brands