background image

Power Rake Safety

Keep away from the rotating teeth while operating
the power rake.

Never directly discharge toward people, animals,
or property.

Never use the attachment to carry loads.

After striking a foreign object, shut off the engine,
remove the key, thoroughly inspect the attachment
for any damage, and repair the damage before
starting and operating the attachment.

Always lower the attachment and shut off the
machine each time you leave the operating
position.

Maintenance and Storage
Safety

Check fasteners at frequent intervals for proper
tightness to ensure that the equipment is in safe
operating condition.

Refer to the

Operator’s Manual

for important

details if you store the attachment for an extended
period of time

Maintain or replace safety and instruction labels,
as necessary.

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or lost.

decal93-9367

93-9367

1.

Crushing hazard of hand—keep hands away.

decal100-4708

100-4708

1.

Thrown object hazard—keep bystanders away.

decal93-7321

93-7321

1.

Cutting/dismemberment hazard of hands and feet, rotating
knives/blades—stay away from moving parts.

decal93-9084

93-9084

1.

Lift point

decal115-2903

115-2903

1.

Grease

4

 

Summary of Contents for 22426





















Reviews: