manualshive.com logo in svg

Tornatech GPU, Installation And Maintenance Manual, Page: 50 / 67

Share
Download
Tornatech GPU Installation And Maintenance Manual Download Page 50

 

 

50 

 

 

The small white circle beside each signal is a representation of its state. If the white circle is filled with a green dot, 
then the signal is activated. Comparing these software signals and the physical state of the signal on the electronic 
board is the best way to troubleshoot. In the right column, additional “TEST” buttons are located beside each output 
signal. Clicking on these buttons will toggle the output state of this signal, again allowing a comparison between the 
software and hardware state of these signals to help troubleshoot. 
 

Inputs/Outputs Debug 

Config > Advanced > Debug > Expansion 

 

The small white circle beside each signal is a representation of its state. If the white circle is filled with a green dot, 
then the signal is activated. The first element in the left column is the indication of whether or not the optional 
Expansion board is installed. In the box, the corresponding Expansion board number is displayed. Comparing 
between these software signals and the physical state of the signal on the electronic board is the best way to 
troubleshoot. In the 

right column, additional “TEST” buttons are located beside each output signal. Clicking on these 

buttons will toggle the output state of this signal, again allowing a comparison between the software and hardware 
state of these signals to help troubleshoot. 

Summary of Contents for GPU




































































Reviews:

No comments