background image

Vers.2016/02 

12 

 
 

You must observe the following points in the interest of your own 

safety!!! 

 
Safety instructions: 
 

 

The TORNADOR-GUN causes considerable noise pressure. Please wear hearing protection in order 
to avoid noise which can be damaging to your health. 

 

When working with the TORNADOR-GUN, small parts may be whirled into the air: Wear protective 
goggles to prevent eye injuries. 

 

The TORNADOR-GUN nebulises the cleaning liquid very finely. To prevent health hazards from 
inhalation, wear appropriate respiratory protection. 

 

Ensure all others in the area are wearing impact-resistant eye goggles and face masks. 

 

Do not install a quick coupler directly into the air tool throttle handle. 

 

Only use the TORNADOR-GUN in ventilated spaces. 

 

Never operate the TORNADOR-GUN with more than 8.5 bar (121 psi). We recommend 4.5 to 6.5 bar 
(64 to 93 psi) 

 

Do not use cleaning agents which are acidic, alkali and/or inflammable. We recommend the use of 
neutral cleaning agents. 

 

When using cleaning fluids which need to be diluted, always strictly observe the manufacturer's 
instructions to make sure the mixture is correct. 

 

Never point the TORNADOR-GUN towards the face or body of you or anyone else. 

 

Keep the TORNADOR-GUN out of the reach of children. 

 

To reduce risk of injury, everyone using, installing, repairing, maintaining, changing accessories on, 
or working near this tool must read and understand these instructions before performing any such 
task. 

 

This tool and its accessories must not be modified. 

 

Air under pressure can not be used. 

 

Always shut off air supply, drain hose of air pressure and disconnect tool from air supply, when not 
in use, before changing accessories or when making repairs. 

 

Put never direct air at yourself or anyone else. 

 

Whipping hoses can cause serious injury. Always check for damaged or loose hoses and fittings. 

 

Do not exceed maximum air pressure of 8.5 bar (121 psi) or as stated on the name plate. 

 

Slip, trip and fall are main causes of serious injury or death. Be aware of excess hose left on the 
path or work surface.  

 

Operators and maintenance personnel must be physically able to handle the bulk, weight and 
power of this tool. Further take of a balanced body position and secure footing. 

 

This tool is not intended for use in explosive atmospheres and is not insulated for contact with 
electric power sources. 

 

Be prepared that the material of your tool always can have material tiredness. 

 

We recommend you never clean any safety-related components, e.g. safety belts, electrical or 
electronic modules, with the TORNADOR-GUN. 

 
Special instructions: 
The written and spoken information and recommendations which we provide to support the purchase/user, 
are the result of previous experience and the latest findings. Because of the manifold possibilities for use and 
processing conditions, this information is without obligation and do not constitute a contractual legal 
relationship or any supplementary obligations of the sales contract. 
In any event, the purchaser holds responsibility for checking suitability for the intended use himself. Always 
read the safety warnings for cleaning liquids and contact the manufacturer in case of doubt. 
Our liability and responsibility is based exclusively on our general terms and conditions of business and are 
not expanded on by either this information or the technical advice of our technical field staff. 

 
 

 
 

Summary of Contents for Z-020S










Reviews: