background image

 
 
 
 

 

LIMITED WARRANTY 
Toni warrants this product for a period of 1 year. It is a limited warranty. You must  
complete the warranty certificate in full, immediately when you purchase this machine.  
You must fax, or scan and email as per instruction on the warranty certificate. 
 
 
WHAT THIS WARRANTY COVERS:

 

This warranty covers all defects in workmanship 

and materials for a period of 1 year from the date of purchase, provided that: 
a/. The table saw has been used in accordance with the manufacturer’s intended use. 
b/. During the warranty period service and repairs must be carried out by authorized 
service centre using original parts. 
c/. The unit is serviced regularly (after every 10 hours of usage). 
 
 
We will repair any faulty workmanship, and either repair or replace any defective part, 
at our discretion. We will do so without any charge. We will complete the work in a 
reasonable time, but, in any case, within ninety days or less. PROOF OF PURCHASE 
NEEDS TO BE PRODUCED and  the Warranty Certificate, with any warranty claim. 
 
 
WHAT’S NOT COVERED UNDER WARRANTY: This warranty applies only to the  
original purchaser at retail and may not be transferred. This warranty only covers  
defects arising under normal usage and does not cover any malfunction, failure or  
defects resulting from misuse, abuse, neglect, alteration, modification or repairs by other  
than Toni approved service agents. It does not cover the accessories. It does not cover  
the fair wear and tear of the parts. Brushes, bearings and accessories are normal wear  
and tear parts. This warranty does not cover commercial use of the tool. 
 
 
ADDITIONAL LIMITATIONS:  This warranty is limited to a period of  1 years from the  
date of purchase. Toni is not responsible for direct, indirect, or incidental damages, for  
the failure of the product. Toni will not be responsible for any damages or personal  
injury caused by the use, misuse or failure of the product, under any circumstances. 
 
 
HOW TO GET SERVICE:  Return the power tool, properly packaged and postage  
prepaid, to an Authorized Service Center or your dealer. You can obtain the location of  
the Service Center nearest to you by contacting a service representative at 
 [email protected] or [email protected] . To request your warranty service,  
you must present the warranty certificate with the proof of purchase documentation, and  
all the necessary packaging and accessories. 
 
 
 
 

KEEP THIS INSTRUCTION MANUAL & WARRANTY 

CONDITIONS FOR FUTURE REFERENCE. 

 
 

WARRANTY 

19 

 

Summary of Contents for TMS210F




















Reviews: