Tohnichi DOTE100N4-G Operating Instruction Download | Manualshive

Page: 23 / 28

background image

20

D

IGIT
AL T

ORQUE WRENCH TES

TER
D

O

TE4-G

8-3. Operation with Communication Command

Setting of DOTE4-G can be changed by communication command from an external device.
DOTE4 executes the command and sends back response command to the external device.
(1) Communication commands

All commands are ASCII code
Append CRLF in the end of command

(2) Communication example

• In case of switching upper limit setting (A)

• In case of setting upper limit at 50.00 and lower limit at 40.00

Command

Motion

AT219 ,*

Switch registered upper/lower limit. * must be A:0,B:1,C:3…J.9

AT037,******,******

Register upper limit and lower limit at the same time.

* must be torque value in 6 digits including decimal point.

AT023,*******

Register 7-digit alphanumeric.

* must be upper case alphabet or number.

Registered 7-digit alphanumeric is appended to measurement data.

«
...
21
22
23
24
25
...
»

Summary of Contents for DOTE100N4-G





























Reviews:

No comments

Related manuals for DOTE100N4-G

Brand: ACS Pages: 56

Brand: Tanco Pages: 72

Brand: HABYS Pages: 16

Brand: Acterna Pages: 72

Giraffe OmniBed

Brand: Ohmeda Pages: 54

Ettan IPGphor 3

Brand: GE Pages: 64

Brand: GE Pages: 56

Brand: GE Pages: 132

Brand: GE Pages: 16

Brand: GE Pages: 474

Brand: Yardistry Pages: 9

Brand: Jackco Pages: 6

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: K-9 Lights Pages: 12

Brand: K'Nex Education Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands