background image

2

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe 

operation.

•  Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or 

cautions regarding safety.

•  After reading, keep this manual handy for future reference.

Safety Symbol and Message Conventions 

Safety symbols and messages described below are used in this manual to prevent bodily injury and property 

damage which could result from mishandling. Before operating your product, read this manual first and 

understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards. 

Indicates a potentially hazardous situation which, 

if mishandled, could result in death or serious 

personal injury. 

WARNING

When Installing the Unit

• Do not expose the unit to rain or an environment 

where it may be splashed by water or other liquids, 

as doing so may result in fire or electric shock. 

•  Use  the  unit  only  with  the  voltage  specified  on 

the unit. Using a voltage higher than that which is 

specified may result in fire or electric shock.

• Do not cut, kink, otherwise damage nor modify 

the power supply cord. In addition, avoid using the 

power cord in close proximity to heaters, and never 

place heavy objects -- including the unit itself -- on 

the  power  cord,  as  doing  so  may  result  in  fire  or 

electric shock. 

• Avoid installing or mounting the unit in unstable 

locations, such as on a rickety table or a slanted 

surface. Doing so may result in the unit falling 

down and causing personal injury and/or property 

damage. 

•  Install the unit only in a location that can structurally 

support the weight of the unit and the mounting 

bracket. Doing otherwise may result in the unit 

falling down and causing personal injury and/or 

property damage.

When the Unit is in Use

• Should the following irregularity be found during 

use, immediately disconnect the power supply plug 

from the AC outlet and contact your nearest TOA 

dealer. Make no further attempt to operate the unit 

in this condition as this may cause fire or electric 

shock.

· If you detect smoke or a strange smell coming 

from the unit

·  If water or any metallic object gets into the unit 

· If the power supply cord is damaged (exposure of 

the core, disconnection, etc.)

·  If it is malfunctioning (no tone sounds.)

•  To prevent a fire or electric shock, never open nor 

remove the unit case as there are high voltage 

components inside the unit. Refer all servicing to 

qualified service personnel.

•  Do not insert nor drop metallic objects or flammable 

materials in the ventilation slots of the unit's cover, 

as this may result in fire or electric shock.

•  Do not touch a plug during thunder and lightning, as 

this may result in electric shock. 

Indicates a potentially hazardous situation which, 

if mishandled, could result in moderate or minor 

personal injury, and/or property damage.

CAUTION

When Installing the Unit

•  Never plug in nor remove the power supply plug with 

wet hands, as doing so may cause electric shock.

•  When unplugging the power supply cord, be sure to 

grasp the power supply plug; never pull on the cord 

itself. Operating the unit with a damaged power 

supply cord may cause a fire or electric shock.

•  Be sure to follow the instructions below when rack-

mounting the unit. Failure to do so may cause a fire 

or personal injury.

·  Install the equipment rack on a stable, hard floor. 

Fix it with anchor bolts or take other arrangements 

to prevent it from falling down. 

·  When connecting the unit’s power cord to an AC 

outlet, use the AC outlet with current capacity 

allowable to the unit. 

· The supplied rack-mounting screws can be used 

for the TOA equipment rack only. Do not use them 

for other racks.

When the Unit is in Use
•  Do not place heavy objects on the unit as this may 

cause it to fall or break which may result in personal 

injury and/or property damage. In addition, the 

object itself may fall off and cause injury and/or 

damage.

•  Do not stand or sit on, nor hang down from the unit 

as this may cause it to fall down or drop, resulting in 

personal injury and/or property damage.

Summary of Contents for N-8000DI













Reviews: