background image

 

172-65254MA-04  (A-COS-10)    22  Apr  2020

 

4

 

Specifications 

 

 

Install properly and DO NOT use this product outside the recommended 

operating pressure, temperature and other specification ranges. 

Improper use may result in such hazards as damage to the product or 

malfunctions which may lead to serious accidents. Local regulations 

may restrict the use of this product to below the conditions quoted.

 

CAUTION 

 

 

 

DO NOT use the product in excess of the maximum operating pressure 

differential;  such use could make discharge impossible (blocked).

 

CAUTION 

 

 

Use only under conditions in which no freeze-up will occur. Freezing 

may damage the product, leading to fluid discharge, which may cause 

burns or other injury.

 

CAUTION 

 

Refer to the product nameplate for detailed specifications.   

Model

Nominal Diameter

Maximum Operating 

Temperature

Valve No.*

Secondary Pressure 
Adjustable Range

Primary Pressure
Range

Production Lot No.

 

* Valve No. is displayed for products with options. This item is omitted from the nameplate 

when there are no options. 

 
 
 

Acceptable Operating Range 

Model 

A-COS-10 

Applicable Fluid 

Air 

Primary Pressure Range 

0.1 to 0.9 MPaG (15 to 130 psig) 

Secondary Pressure Adjustable Range 

0.05 to 0.7 MPaG (7 to 100 psig) 

Minimum Differencial Pressure 

0.05 MPa (7 psi) and larger 

Maximum Operating Temperature 

100 °C (212 °F) 

Minimum Adjustable Flow Rate 

10% of rated flow rate and larger 

     

(1 MPa = 10.197 kg/cm

2

)

 

 

 

Summary of Contents for A-COS-10
























Reviews: