background image

 

Program operation 

Place the photometer head in parallel to the plane of the item which is being measured. See to it that 
the  shadow  of  the  operator  who  conducts  the  measurement  does  not  cast  itself  onto  the  photohead 
window, as well as the shadow of any irrelevant objects that are temporarily present. 
Upon being started, the program scans the USB bus and in case the device is detected displays 

Ready

 

in the status line and starts automatically to display the data received from the photohead. When there 
is no connection, the program displays 

Searching… 

in the status line. 

The four buttons of the control panel are designed for storing data being received into a text file, the 
spectrum graph into a file, setting up the program, and outputting additional information correspond-
ingly. The spectrum graph is stored in BMP format.  
For the user’s convenience data are stored into a text file also through pressing the button 

ENTER

.  

 

The 

name 

of 

the 

file 

in 

this 

case 

is 

formed 

automatically 

in 

the 

format 

tka_data_YYYYMMDD_HHMMSS

. The obtained file can be downloaded into any word processor 

or electronic table for further processing. 
 
 

Storage and transportation rules 

The device  must  be  stored  in  a dry  heated room  under  the  conditions corresponding  to the group  1 
GOST15150-69 at the tempe5 to +40 

0

С and relative humidity not above 85% at 25

0

С. 

The air in the room should not contain admixtures of aggressive vapors or gases. 
The transportation of the devices in the manufacturer’s packing can be made by any closed transport 
without  speed  limitations GOST  15150-69  at the ambient  temperature  from  10 below zero to  60 

0

С 

above zero and relative humidity up to 98% at the temperature 35 

0

С. After transportation at tempera-

ture below 0

0

С it should be unpacked should only be effected after holding it in the packed condition 

at the temperature (20±5) 

0

С for at least 12 hours. 

Air transportation is not allowed. 
 

An acceptance certificate 

The device UV-Radiometer ТКА-UV, factory No. 
                                    is acknowledged ready for operation. 

 

Date of release: “____” _______ 200 

 

Stamp  QCD: ___________________________________ 

 

Date of sale: “____” _____________ 200___  
 

Generated by Foxit PDF Creator © Foxit Software

http://www.foxitsoftware.com   For evaluation only.

Summary of Contents for UV-Radiometer
























Reviews: