background image

Zephyr

 3 – Heating/Cooling  

Controller Overview

The Zephyr

 3 is used to maintain the temperature level in your growing environment. 

The temperature can be adjusted by setting the dial on the front of the controller to your 
preferred setting. When the Zephyr

 3 is in the COOLING MODE and the temperature 

exceeds the predetermined setting, the piggyback cord set is activated and will operate the 
exhaust fan until the temperature is lower than the preferred set point.  When the Zephyr

 

3 is in the HEATING MODE and the temperature is below the predetermined setting, then 
the piggyback cord set is activated and will operate the heater (1500 Watts or less) until the 
temperature is higher than the preferred set point. The Zephyr

 3 operates up to 15 amps 

maximum capacity on a standard 120 Volt circuit. Built with the highest quality components, 
the Zephyr

 3 will provide the user with years of trouble free service. Controllers created for 

our industry, by our industry!

Instructions for Operation

•  Securely mount your Zephyr

 3 in your grow area and away from any moisture, spray, 

pesticides, etc. using the hardware provided.

•  Set green rocker switch in either COOLING or HEATING mode.

•  Plug the exhaust fan or heater into the piggyback cord set.

•  Turn the fan ‘ON’ to the fastest setting possible, if adjustable.

•  OR set the heater at the highest setting possible, if adjustable.

•  Set the ‘Temperature’ dial at the preferred temperature level for your garden.

•  Finally, plug the Zephyr

 3 into a dedicated 120 Volt – 15 Amp power source.

•  Use of a surge protection device is recommended to protect your Zephyr

 3 from 

potential power damage in areas where this may be an issue.

•  Your Zephyr

 3 will now control your equipment at the desired setting.

 

Troubleshooting Tips

If the Zephyr

 3 is not performing as expected, try the following:

a. Confirm that your power input source is active by using a voltage test meter, and verify 

that the power input source is providing 120 Volts of power to the Zephyr

 3.

b. Validate that the power outlet of the Zephyr

 3 is active by setting the switch in the 

COOL mode and put the temperature dial at the lowest setting. Then use a voltage test 
meter to verify power is flowing through the controller to the power outlet.

Warranty Information

• Titan Controls

®

 warrants the original purchase of this product against defects in material 

and workmanship under normal use for three (3) years from the date of purchase.

• During the warranty period, Titan Controls

®

 will, at our option, and without charge, repair or 

replace this product if the controller or any of its components fail or malfunction.

• All returns or repairs must be accompanied by a Return Merchandise Authorization (RMA) 

number prior to any service of the product.

• This warranty is expressly in lieu of all other warranties, expressed or implied, including the 

warranties of merchantability and fitness for use and of all other obligations or liabilities on 
the part of the seller.

• This warranty shall not apply to this product or any part thereof which had been damaged 

by accident, abuse, misuse, modification, negligence, alteration or misapplication.

• Controllers with serial numbers or date tags that have been removed, altered or obliterated; 

broken seals or that show evidence of tampering; mismatched board serial numbers or 
nonconforming parts; are excluded from coverage.

• Titan Controls

®

 makes no warranty whatsoever in respect to accessories or parts not 

supplied by Titan Controls

®

.

• Monetary refunds of the warranty will not be given.

• The Buyer assumes all responsibility regarding the use & installation of this controller.

• All warranty service is provided through the factory or an authorized service representative.

• This warranty shall apply only to the United States, including Alaska, Hawaii and territories 

of the United States.

• Defective controllers need to be returned with the “proof of purchase” receipt.

• For additional warranty information, contact a Titan Controls

®

 Technical Service 

Representative or your Dealer.

• NOTE: Titan Controls

®

 is a controller manufacturer. All sales offerings to the public are 

done through a nationwide group of Dealers. No sales offerings will be made directly to the 
general public.

Service and Repair Program

• For all service and repairs please contact our Technical Service Representative for a Return 

Merchandise Authorization (RMA) number.

• All factory service & repairs will be completed within 48 hours of receipt of controller and 

after authorization by customer for repairs.

• Titan Controls

®

 will, at its discretion, repair or replace the controller.

• Factory calibration services are available for all Titan Controls

®

• Returning Units: Please contact your retail store for returns. 

6

3

Reviews: