background image

PK-232 – MBX OPERATING MANUAL

COMMAND SUMMARY

4/91

A-32

157

CRA

dd ON|OFF

Default: OFF

Mode: Baudot RTTY

Host: CR

Parameters:

ON -

Send <CR><CR><LF> in Baudot RTTY.

OFF - Send <CR><LF> in Baudot RTTY (default).

The  CRADD  command  permits  you  to  set  the  PK-232's  "newline"  sequence  so  that  an  additional
carriage return is ADDed automatically at the end of each typed line.

When CRADD is ON the line-end sequence is <CR><CR><LF>. When CRADD is OFF the line-end
sequence  is  <CR><LF>.  The  double  carriage  return  is  required  in  some  RTTY  services  such  as
MARS. CRADD has no effect on received data.

CS

tatus [Short]

Immediate Command

Mode: Packet

Host: Not Supported

CSTATUS is an immediate command helpful in multiple connections.

When CSTATUS is typed, your monitor displays Link State of all ten logical channels as well as the
current input/output channel as follows:

NOT CONNECTED TO ANY STATION

CONNECTED TO TWO STATIONS

cmd:cs

cmd:cs

Ch. 0 - IO DISCONNECTED

Ch. 0 - IO CONNECTED to WX1AAA

Ch. 1 -    DISCONNECTED

Ch. 1 -    CONNECTED to WX1BBB

Ch. 2 -    DISCONNECTED

Ch. 2 -    DISCONNECTED

Ch. 3 -    DISCONNECTED

Ch. 3 -    DISCONNECTED

Ch. 4 -    DISCONNECTED

Ch. 4 -    DISCONNECTED

Ch. 5 -    DISCONNECTED

Ch. 5 -    DISCONNECTED

Ch. 6 -    DISCONNECTED

Ch. 6 -    DISCONNECTED

Ch. 7 -    DISCONNECTED

Ch. 7 -    DISCONNECTED

Ch. 8 -    DISCONNECTED

Ch. 8 -    DISCONNECTED

Ch. 9 -    DISCONNECTED

Ch. 9 -    DISCONNECTED

CSTATUS will give a short display if desired. CSTATUS SHORT (or CS S) displays only the current
input/output channel or those channels which are connected.

CT

ext text

Default: empty

Mode: Packet

Host: CT

Parameters:

text - Any combination of characters up to a maximum of 120 characters.

CTEXT is the "automatic answer" text sent when CMSG is ON. The message is sent only when an-
other station connects to you. A typical CTEXT message might be:

I'm not available right now. Please leave a message on my MailDrop.

Clear CTEXT with 

%

&

NO

NONE

 or 

OFF

, or simply set CMSG OFF.

Summary of Contents for PK-232MBX








































































































































































































































Reviews: