manualshive.com logo in svg

TigerStop TigerSaw Miter, Owner'S Manual

Share
Download
TigerStop TigerSaw Miter Owner'S Manual Download Page 45

39

Common TigerStop Parts

Common TigerTurbo Parts

Part number

Part name

Description

ATB**

TigerStop belt

belt connecting motor to pusher

** is the working length of the TigerStop in feet

IES2-**

idle end sensor

optical end sensor (far from motor)

** is the working length of the TigerStop in feet

MES2

motor end sensor

optical end sensor (near motor)

MOT2

TigerStop motor

drive motor for TigerStop

TigerStop

Serial Number

• 

The working length of the TigerStop is 2 feet (0.6 m) less than the overall length of the TigerStop.

Part number

Part name

Description

DB-TT

TigerTurbo drive belt

belt connecting motor pulley to large pulley

AT5-TT-**

TigerTurbo large belt

belt connecting large pulley to pusher

** is the working length of the TigerTurbo in feet

MOT-TT

TigerTurbo motor

drive motor for TigerTurbo

SB7249

TigerTurbo motor cable

Cable between amplifier and motor

Serial

Number

• 

The working length of the TigerTurbo is 3 feet (0.9 m) less than the overall length of the TigerTurbo.

Replacement Parts

Summary of Contents for TigerSaw Miter





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands