manualshive.com logo in svg

TigerStop TigerSaw Miter, Owner'S Manual

Share
Download
TigerStop TigerSaw Miter Owner'S Manual Download Page 11

5

There are three access doors on the TigerSaw Miter.  
Each access door is equipped with a separate safety switch.

Saw Operation

Access Doors and Safety Switches

Emergency Stop Switch

The emergency stop (E-stop) switch is located on the front of the cabinet, 

just below the handle for the tabletop guard door. 

Pressing the E-stop switch will immediately stop the saw motor, retract the 

blade, and release the top cap.

Before operation can begin again, the E-stop condition must be released by 

rotating the switch clockwise.

Tabletop Guard Door

The tabletop guard door opens upward with the 

pictured handle, allowing routine access to the 

work area for regular cleaning and for adjusting 

material if necessary. 

The safety switch on the tabletop guard door 

stops the saw motor and the saw stroke when 

the tabletop guard door is opened.  This switch 

also prevents activation of the saw motor until the 

tabletop guard door is closed again.  

• 

The blade will continue spinning in the 

cabinet base for some time after the motor 

stops.

Warning: DO NOT disable or bypass the safety switches.  

Replace failed safety switches immediately.

Summary of Contents for TigerSaw Miter





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands