TigerStop TigerSaw 1000 Installation Manual Download Page 48 | Manualshive

Page: 48 / 68

background image

45

You can still mark defects in grade 1 and TigerSaw will continue to cut parts inside of Grade 1. You

may also enter and leave Grade 2 at any time on the material.

Adjustment Points

Pneumatic adjustment points

The pneumatic system has adjustments for the air pressure to the system, as well as a number of

flow adjustment points that can determine the cycling speed of the saw.

Adjusting System Air Pressure

Total system air pressure will need to be set at 80 PSI. The air control is on the back of TigerSaw.

The cap can be turned to increase or decrease total system air pressure. The pressure gauge on

the air prep module will tell you the current air pressure in the system.

Adjusting Flow to the Top Cap

The cylinder that controls the saw top cap has a flow adjustment on both cylinder ports. This will

speed up or slow down the top cap.

Note: Always power down and follow all lockout/tag out procedures before opening any saw access door.

To access the top cap cylinder...
1. Loosen the bolts holding the access cover.
2. Lift up and pull the cover away.

«
...
46
47
48
49
50
...
»

Summary of Contents for TigerSaw 1000





































































Reviews:

No comments

Related manuals for TigerSaw 1000

Brand: Keithley Pages: 36

Brand: Rain-Flo Irrigation Pages: 16

Brand: Panasonic Pages: 174

Brand: Facnor Pages: 33

Brand: Gaspardo Pages: 16

Brand: Gastrodomus Pages: 4

Brand: HANYOUNG NUX Pages: 2

Brand: Gastrodomus Pages: 39

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: Xiitech Pages: 6

Brand: tayco Pages: 111

Brand: Pari Pages: 282

APT-9411 Series

Brand: TAKAYA Pages: 77

Brand: Tadano Pages: 402

Brand: XanLite Pages: 4

Brand: Emos Pages: 8

Brand: DALBO Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands