TigerStop TigerSaw 1000 Installation Manual Download Page 42 | Manualshive

Page: 42 / 68

background image

39

Quick Calibration

The quick calibration is a short cut to the calibration setting.

1.Start at the ready screen. Press the [Calib] soft key.

Note: If you are viewing the expanded options, press [Cancel] to go back.

2.Cut a sample piece and measure its length.

3.Enter the length of the sample piece. Press the [Done] soft key.

For this example I have measured 33.935 as my cut length.

4.TigerStop is now calibrated.

To download the complete TigerStop operation manual, visit our website www.tigertamer.com.

Basic TigerSaw Operation

Power Up TigerSaw

Once all the interlocks are reset, the green “Safety Chain” light will light up. Press the green side of

the “Saw” power switch. This will engage the saw pneumatics and will start the saw blade motor. Press
the red side of the “Saw” power switch to turn off the pneumatics and motor.

Warning! Use hearing and eye protection when using TigerSaw.

Saw Interlocks

The guard door and the saw blade access door will lock shut when the saw blade is running. Do not

attempt to access these areas when the saw blade is running.

Triggering an E-Stop

When the saw blade is running there are two ways to trigger an emergency stop.

E-Stop Button

«
...
40
41
42
43
44
...
»

Summary of Contents for TigerSaw 1000





































































Reviews:

No comments

Related manuals for TigerSaw 1000

Brand: Raymarine Pages: 55

Brand: Halyard Pages: 4

Underwater Light Show & Fountain

Brand: GAME Pages: 2

Brand: jablotron Pages: 2

Brand: Nectar Pages: 46

Brand: Neauvia Pages: 17

Brand: Valko Pages: 10

Brand: CombiSteel Pages: 60

Brand: Lightolier Pages: 2

Brand: Ametek Pages: 20

L10 LVELED Series

Brand: Clevetronics Pages: 2

Brand: Goobay Pages: 20

Brand: NEBO Pages: 2

ANY SPOT AS-1400-2P

Brand: Galaxy Audio Pages: 12

Brand: Knightsbridge Pages: 4

Brand: Pepperl+Fuchs Pages: 2

Brand: Studiomaster Pages: 10

Fold Away Strength Trainer F3

Brand: Torque Fitness Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands