manualshive.com logo in svg

Tiffen Steadicam M-2, System Manual, Page: 7 / 54

Share
Download
Tiffen Steadicam M-2 System Manual Download Page 7

7

Volt gimbal connector

LEMO® 8-pin 1B connector

Rotates 90˚ for cable routing

Included on ALL top stages

Front Electronics

Tally IN/OUT port

LEMO® 4-pin 0B connector

Use with available tally sensor

Triple 12/24V ports

LEMO®

 

3-pin 0B connectors

Outer port rotates 90˚

12 volts supplied at all times

12 and 24 volts simultaneously 

      when in 24V mode

Dual P-Tap ports

12 volts supplied at all times

Oriented for cable management

Self-resetting 5A fuse protected

Rear Electronics

Camera power port

LEMO® 3-pin 2B connector

12 volts supplied at all times

12 and 24 volts simultaneously   

       when in 24V mode

Triple HD video ports

HD-SDI compatible 

Direct connections to the base

Color coded at each end

NOTES: 

Tally sensitivity is set at maximum from the factory with active LO tally input signal, and this should work for most users. 

Contact Tiffen service for instructions on adjusting tally sensitivity and setting to active HI, if required.

Also, there is a covered micro-USB port on the underside of the stage. This is ONLY for Volt firmware updates at the factory.

Inputs and outputs

Summary of Contents for Steadicam M-2























































Reviews:

No comments