Tibbo DS10x0 Page 455 Programmable Hardware Manual Download | Manualshive

Page: 455 / 570

background image

444

Tibbo Project System (TPS)

© Tibbo Technology Inc.

Running

journalctl

will present every entry in the journal, starting with the oldest

entries. You can scroll through the entries with the Page Up and Page Down keys,
and exit by pressing Q.

If you would like to see only the journal entries for the current boot, run

journalctl -

b

.

To see journal entries for specific time frames, you can use the --

since

and/or --

until

options. These options must be followed by either relative values — yesterday,

today, tomorrow, or now — or absolute time values, which take the format "YYYY-
MM-DD HH:MM:SS" and must include the quotes. For example, running

journalctl --

since "2020-07-21 12:00:00"

would display all journal entries recorded since noon on

June 21, 2020.

Perhaps the most useful way of filtering the journal is by unit, or services being run
on the system. For example, running

journalctl -u ag_server

would display all journal

entries related to AggreGate Server events.

Finally, this utility can be used to monitor the journal and display entries as they are
created in real time by running

journalctl -f

. To stop following, press Ctrl+C.

For more details about

journalctl

,

please consult its man page

Monitoring system load

The default CLI utility to monitor system load on most Linux distributions is

top

. This

interactive tool displays near-real-time information about CPU and RAM usage, as
well as active processes and how much CPU time they are consuming, among other
data. To exit the utility, press Ctrl+C.

Information on using the powerful interactive features of

top

is easily found online.

Checking disk space

To see the size and usage of all media mounted on the system, you can run

df

to

display the information in 1K blocks. If you would prefer output in units more
commonly used on a daily basis, run

df -h

to display the information in kilobytes (K),

megabytes (M), and gigabytes (G).

The partition most likely to be of interest will be mounted on root (i.e., "/").

Managing networking functionality

The powerful iproute2 collection of utilities is available on Tibbo devices running
Linux. This software package replaces several legacy tools for controlling and
managing a wide range of aspects of networking in a Linux system.

The most commonly used utility in the collection is

ip

, which is used to query and

configure the system's networking settings, including IP address, link configuration,
routing tables, and tunnels. One of the most common use cases is getting a network
adapter's IP address, which is accomplished by running

ip address show

.

For more information on all of the functionality provided by iproute2,

please refer to

its online documentation

.

External Controllers

The following external controllers and controller families are currently being offered
by Tibbo:

·

«
...
453
454
455
456
457
...
»

Summary of Contents for DS10x0



























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DS10x0

Brand: Eaton Pages: 50

Brand: Eaton Pages: 166

Brand: NEC Pages: 146

Brand: Garmin Pages: 4

Brand: Samson Pages: 48

Brand: Tamas Pages: 12

Brand: ZIMMERLI MESSTECHNIK Pages: 12

Brand: ABB Pages: 17

Brand: Game ready Pages: 24

Ambience Control 1

Brand: EuroLite Pages: 20

Brand: SKF Pages: 88

Chromoflex Pro Series

Brand: Barthelme Pages: 6

Brand: AUMA Pages: 168

ADAP-KOOL AK-PC 781

Brand: Danfoss Pages: 142

Brand: Calmotion Pages: 9

Brand: Powtran Pages: 36

Brand: Schell Pages: 16

Brand: Hach Pages: 504

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands