manualshive.com logo in svg

Tianlong Gentier 48E, User Manual

Share
Download
Tianlong Gentier 48E User Manual Download Page 28

 

 

14 

Gentier Real-Time PCR System

 

 

 

D. Application Software Operation   

The software  operation  instructions of  the  Gentier real-time PCR system mainly including the 
introduction  of  basic  software  functions  and  operation  descriptions,  such  as  user  account 
managment,  new  experiemtn  creation  and  edition,  real-time  monitoring  and  experiment  data 
analysis, etc.   

Among  all  the  48  throughputs  Gentier  instrument  models,  Gentier  48E  instrument  model 
possesses  the  most  comprehensive  functions. Therefore,  the  Gentier  48E  instrument  model  is 
taken as an example for the function and operation description in this user manual, the instrument 
and software interface figures presented herein are all based on Gentier 48E instrument model. 
For different Gentier instrument models, the software interface will display the corresponding 
features and instrument model names, this user manual will specify the differences of software 
interfaces or functions.   

1. Startup Application Software   

After successfully installing the application software on the control computer,  user can double 
click the 

  icon on the desktop or click the application software file on the start menu to startup 

the Gentier real-time PCR application software. The Welcome screen of the application software 
is as shown in figure D-1.   

 

Figure D-1. Welcome screen of the Gentier real-time PCR application software 

Summary of Contents for Gentier 48E












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands