background image

1

Thunder Tiger Trainer MK II Super Combo/Combo Plus/TRTF (TTR4523)

Distributed in North America by Ace Hobby Distributors, Inc.

116 W. 19th ST, Higginsville, MO  64037

Phone: (660)-584-7121 • www.acehobby.com • email: [email protected]

Tiger Trainer MK II

Assembly Manual

Wingspan:

61”

Length:

51”

Wing area:

675 in

2

Weight:

5-5.5lbs

Engine:

.40-45

Radio:

4 Channel

Specifications:

Warranty

This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.

It does not cover any damage caused by use or modification. The warranty does not extend beyond the
product itself and is limited only to the original cost of the kit. By the act of building this user-assembled
kit, the user accepts all resulting liability for damage caused by the final product. If the buyer is not 
prepared to accept this liability, it can be returned new and unused to the place of purchase for a refund.

99211/JE6131

Notice: Adult Supervision Required

This is not a toy. Assembly and flying of this product requires adult supervision.

Read through this book completely and become familiar with the assembly and flight of this airplane.

Inspect all parts for completeness and damage. If you encounter any problems, call 660-584-6724 for help.

Summary of Contents for Tiger Trainer MK II













Reviews: