Thrane&Thrane SAILOR TT-3000E mini-C GMDSS System Installation Manual Download

Page: 92 / 97

TT-3000E mini-C GMDSS System

Installation Manual

9.3

TT-3042C

PECIFICATIONS

Model TT-3042C,

Remote Alarm/Distress Box

General Specifications

The unit is in full compliance with the
Inmarsat CN114, IEC 60945 and Wheel
Mark specifications.

Dimensions (H x W x D)

49 mm x 95 mm x 99 mm

Weight 0.32

Mountings

Wall mounting, 4 holes Ø4.0 mm
Mounting bracket for console, 4 holes
Ø4.0 mm

Power requirements

7.5V - 12V DC,
Standby: 0.1W @ 9V
Max.:

0.5W @ 9V

Cable length / Type

Max. 100m / 8 wire, screened signal
cable, 0.25mm

or better.

Connector Internal

screw

terminals

Distress/MES Fault Relay

Max. switching: 2A or 60W or 220V AC

Distress Relay jumpers

Enable; W1: 1-2,

Disable; W1: 2-3 ††

Activated:

Shorted; W2: 1-2 ††,

Open;

W2:

2-3

MES Fault Relay jumpers

Enable; W3: 1-2,

Disable; W3: 2-3 ††

Activated:

Open;

W4: 1-2 ††,

Shorted;

W4:

2-3

Temperature

-25°C to 55°C operating,
-40°C to 80°C storage

Relative humidity

95% non-condensing at 40°C

Vibration operational

Random vibrations:

5-20 Hz:0.005 g²/Hz

20-150 Hz:-3 dB/oct

(0.5

rms.)

Sinusoidal vibrations: 2-15.8 Hz: 2.54 mm
peak

ampl.

10-100 Hz: 1.0 g

peak

acceleration

Vibration survival

Random vibrations:

5-20 Hz:0.05g²/Hz

20-150 Hz:-3 dB/oct

(1.7g

rms.)

Sinusoidal vibrations: 2-15.8 Hz:2.54 mm
peak

ampl.

10-100

Hz:

1.0g

peak

acceleration

Shock Half

sine:

20g/11ms

Table 18 TT-3042C Technical Specifications

††: Factory setting

92/97

Summary of Contents for SAILOR TT-3000E mini-C GMDSS System


































































































Search results

Summary of Contents for SAILOR TT-3000E mini-C GMDSS System

Reviews:

Related manuals for SAILOR TT-3000E mini-C GMDSS System

Brands by name

Popular brands

Thrane&Thrane SAILOR TT-3000E mini-C GMDSS System, Installation Manual

Search results

Summary of Contents for SAILOR TT-3000E mini-C GMDSS System

Reviews:

Related manuals for SAILOR TT-3000E mini-C GMDSS System

Brands by name

Popular brands