Thorne BEES ON A BUDGET W.B.C. BEEHIVE Assembly Instruction Manual Download Page 1

Thornes are committed to providing excellent quality beekeeping equipment. We have been making 
beehives for over 100 years now and are in our third, fourth and fifth generations. Many of our staff are 
enthusiastic beekeepers with years of knowledge and experience in the industry. All our full size hives 
are made from Canadian Western Red Cedar and the Budget range usually from British Western Red 
Cedar. Whilst Cedar does not require preservative, having its own camphor type oils, we recommend the 
use of an insecticide free Wood Paint, especially designed for beehives. As an alternative, you can use 
exterior oil. Whether treated or not, your new Thorne beehive should give you many years of trouble-free 
service. 

We also have a dedicated email address if you need help or advice, specifically with beekeeping. 
Please email [email protected].

CONGRATULATIONS ON BUYING A 

BEES ON A BUDGET W.B.C. BEEHIVE

The complete W.B.C. beehive comprises of:
•  Solid Floor and Entrance Slides
•  Cavity Lath
•  Brood Body
•  10 x DN4 frames with standard wired foundation 
•  Dummy board
•  Slotted Steel Queen Excluder
•  2 x Supers 
•  22 x SN4 frames with standard wired foundation
•  3 x pairs of runners
•  Crownboard with two porter bee escapes
•  3 x Lifts (1 x with porch)
•  Plastic cone escapes and brass name plate
•  Gabled roof
•  All nails, screws, pins and glue

PART LIST FOR THORNE’S BUDGET W.B.C. BEEHIVE

We have a YouTube channel: www.youtube.com/thornebeehives
This shows videos on how to assemble your beehive as well as many other useful videos.

Our website is also full of hints tips and PDF documents on how to assemble each part of your beehive.  
You can find them at: www.thorne.co.uk/assembly-instructions

REMEMBER DO NOT GLUE OR NAIL ANYTHING UNTIL YOU ARE SURE THE HIVE PART HAS 

BEEN PUT TOGETHER CORRECTLY.

ASSEMBLY INSTRUCTIONS

E.H. THORNE (Beehives) Ltd.

Beehive Business Park, Rand, Nr. Wragby, Lincolnshire, LN8 5NJ
www.thorne.co.uk        01673 858555        [email protected]

Summary of Contents for BEES ON A BUDGET W.B.C. BEEHIVE












Reviews: