THORLABS PM5020 User Manual Download Page 9

Page: 9 / 65

Page 5

PM5020 Dual-Channel Benchtop Power and Energy Meter

Chapter 2 General Information

Rev: 1.0, 18-Aug-2022

Software Requirements

The PM5020 software is compatible with the following operating systems:

Windows

8.1 (32 bit, 64 bit)

Windows

10 (32 bit, 64 bit)

Chapter 3 Getting Started

3.1 Parts List

Please inspect the shipping container for damage. Please do not cut through the cardboard, as the box
might be needed for storage or returns.

If the shipping container appears to be damaged, keep it until you have inspected the contents for com-
pleteness and tested the PM5020 mechanically and electrically.

Verify that you have received the following items within the package:

1. PM5020 Dual-Channel Optical Power and Energy Meter

2. USB 2.0 Cable, 2 m

3. Two Printed-Circuit Board Connectors - FMC1.5/10-STF-3.5

4. Power Cord, Country Specific

5. Quick Reference

6. Certificate of Calibration

Chapter 4 Operating Instructions

4.1 Operating Elements

Front Panel

Rear Panel

Summary of Contents for PM5020

































































Search results

Summary of Contents for PM5020

Reviews:

Brands by name

Popular brands

THORLABS PM5020, User Manual

Search results

Summary of Contents for PM5020

Reviews:

Brands by name

Popular brands