THORLABS ITC1 Series Operation Manual Download Page 45

Page: 45 / 46

8 Appendix

8.10 Thorlabs Worldwide Contacts

USA, Canada, and South America

Thorlabs, Inc.
56 Sparta Avenue
Newton, NJ 07860
USA
Tel: 973-300-3000
Fax: 973-300-3600

www.thorlabs.com
www.thorlabs.us

(West Coast)

Email:

[email protected]

Support:

[email protected]

UK and Ireland

Thorlabs Ltd.
1 Saint Thomas Place, Ely
Cambridgeshire CB7 4EX
United Kingdom
Tel: +44-1353-654440
Fax: +44-1353-654444

www.thorlabs.com

Email:

[email protected]

Support:

[email protected]

Europe

Thorlabs GmbH
Hans-Böckler-Str. 6
85221 Dachau
Germany
Tel: +49-8131-5956-0
Fax: +49-8131-5956-99

www.thorlabs.de

Email:

[email protected]

Scandinavia

Thorlabs Sweden AB
Bergfotsgatan 7
431 35 Mölndal
Sweden
Tel: +46-31-733-30-00
Fax: +46-31-703-40-45

www.thorlabs.com

Email:

[email protected]

France

Thorlabs SAS
109, rue des Côtes
78600 Maisons-Laffitte
France
Tel: +33-970 444 844
Fax: +33-825 744 800

www.thorlabs.com

Email:

[email protected]

Brazil

Thorlabs Vendas de Fotônicos Ltda.
Rua Riachuelo, 171
São Carlos, SP 13560-110
Brazil
Tel: +55-16-3413 7062
Fax: +55-16-3413 7064

www.thorlabs.com

Email:

[email protected]

Japan

Thorlabs Japan, Inc.
3-6-3 Kitamachi
Nerima-ku, Tokyo 179-0081
Japan
Tel: +81-3-6915-7701
Fax: +81-3-6915-7716

www.thorlabs.co.jp

Email:

[email protected]

China

Thorlabs China
Room A101, No. 100
Lane 2891, South Qilianshan Road
Putuo District
Shanghai 200331
China
Tel: +86-21-60561122
Fax: +86-21-32513480

www.thorlabs.com

Email:

[email protected]

Summary of Contents for ITC1 Series














































Search results

Summary of Contents for ITC1 Series

Reviews:

Brands by name

Popular brands

THORLABS ITC1 Series, Operation Manual

Search results

Summary of Contents for ITC1 Series

Reviews:

Brands by name

Popular brands