GB
1
This universal remote control (2 in 1) is compatible with the majority of television sets, video
cassette recorders, DVD players and satellite recievers as well as DVBT sets (Digital Video
Broadcast Terrestrial) controlled by infra-red commands.
This remote control was programmed in the factory, so that you can use it to control most of
the sets of the THOMSON group’s make. For this reason, we recommend that prior to
attempting to programme the remote control, you try it out by means of one of the methods
described in this user manual. However, first of all, you must install 2 batteries (AAA) in the
remote control.
Please keep this guide along with the code list (provided separately), so that you can
subsequently programme your remote control for use with other sets.
1
On/Standby or Standby only, depending on the
equipment being used.
2
Mode keys. Select the device to control (TV,
DVD, …).
3
Selection of channels, input of digital values,
channels with 2 digits, external TV/VIDEO sources
(AV connectors).
4
Programming of the remote control.
5
Zapping and commands or the muting of sound.
6
Activation and use of menus (display, deletion,
choice, confirmation).
7
Activation and use of teletext (Videotext).
8
Operating a video cassette recorder (VCR) or a
DVD player (DVD).
Use of teletext (Fastext) or functions specific to
certain devices.
Note:
depending on the actual devices, manufacturers
and year of manufacture, the functions available will
vary.
DVBT (Digital Video Broadcast Terrestrial):
for those
countries concerned, you can control a DVBT set by
programming separate codes by using the
DVD/VCR
mode key.
The keys
Testing the remote control
before programming
Programming
the remote control
1. Switch on the set you want to control.
2. Press the key that corresponds to the type of
equipment you want to control:
TV
: television set,
DVD/VCR
: video recorder - DVD player.
3. Direct the remote control towards the TV set and try
to switch it off by simply pressing the key
B
B
. If the
device does not turn off, you must program the
remote control using one of the methods
A
,
B
,
C
or
D
described hereafter.
Note 1:
The
DVD/VCR
mode key can be
programmed to control another device other than
indicated on the key.. It is therefore possible, for
example, to allocate your Satellite mode to the
DVD/VCR
mode key. You must enter the code
corresponding to the manufacturer and the device by
using one of the methods indicated in this manual.
However, method
D
(automatic search for a code)
will greatly simplify the task for you. In this case it is
only necessary to enter a code from the list that
corresponds to the type of device, for example: 0603
for a Thomson satellite receiver) and then to run the
automatic search procedure. The remote control will
then test all the codes automatically until it finds those
that control the receiver.
Note 2:
To control 2 devices of the same type and the
same brand (2 Thomson VCRs, 2 Thomson satellite
receivers, ...) ensure first that these two devices are
not set to react to the same sub code, they will require
one sub code for one and a different sub code for the
other (i.e., codes A and B with Thomson devices).
Once you have checked this, successively program 2
separate mode keys using method
D
.
Method A – Fast programming
with 1-digit subcode
Method B – 4-digit codes
programming
Before you start programming, you must find the
subcode
of the set to be controlled. Entering a sub-
code lets the remote control test a predefined list of
codes. Refer to the list provided with these instructions,
page I of the
subcodes
.
1. Switch on the set you want to control.
2. Hold down the
SETUP
key until the key that
corresponds to the last mode you selected blinks
and then remains lit (the indicator light remains on
for a few seconds to give you the time to proceed
with the following steps. The indicator lamp flashes
to signal that this time is almost up, and then goes
off).
3. Press the key that corresponds to the type of
equipment you want to control:
TV
: television set,
DVD/VCR
: video recorder - DVD player.
4. While the indicator is lit, type in the subcode
(example:
1
for THOMSON).
5. Direct the remote control towards the set and try to
switch it off by pressing the key
B
B
.
6. If the set you want to control switches off, press
OK
to memorise the code.
Note:
If during step 3 you pressed the
DVD/VCR
key,
with identical sub-codes being used to control a VCR or
DVD player, pressing the
B
B
key will turn off the type of
device you have chosen to control.
7. Should the set not switch off, press key
B
B
repeatedly, until the set switches off. Between two
key presses, leave enough time for the key
corresponding to the selected mode enough time to
light up again (about 1 second). Proceeding this
way will enable you to see whether the set responds
or not.
8. Immediately upon the switching-off of the set to be
controlled, press
OK
to store the code.
Check of the programming
:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Before you start programming, you must find the
code
of the set to be controlled.
Refer to the list provided with these instructions, page II
of the
codes
.
1. Switch on the set you want to control.
2. Hold down the
SETUP
key until the key that
corresponds to the last mode you selected blinks
and then remains lit (the indicator light remains on
for a few seconds to give you the time to proceed
with the following steps. The indicator lamp flashes
to signal that this time is almost up, and then goes
off).
3. Press the key that corresponds to the type of
equipment you want to control:
TV
: television set,
DVD/VCR
: video recorder - DVD player.
4. While the indicator is lit, enter the first digit of the
4-digit code proposed for the set to be controlled
(example:
0036
for Thomson).
5. Direct the remote control towards the set and try to
switch it off by pressing the key
B
B
.
F01_GB_ROC2407 5/02/07 10:57 Page 1
