background image

 

Installation and Operating Manual 

Stratotimer ST3

 

 

31-20-01 

Page 2 
 

INTRODUCTION 

Revision: 1.00 

12/06/2020 

 

5.  Technical Support 

Please  contact  Thommen  Aircraft Equipment AG at the address given below for technical 

support. 

THOMMEN AIRCRAFT EQUIPMENT AG 

Hofackerstrasse 48  

CH-4132 Muttenz 

Switzerland 
Phone:  

+41 (0)61 965 22 22  

Email:  

[email protected] 

Internet: 

www.thommen.aero 

6.  Installer Responsibility 

The installer  is responsible for the correct installation of  the  equipment. This includes the 

mechanical and electrical configuration and compatibility with the aircraft. 
All installation personnel must be fully qualified and approved to do the work procedures given 

in this Installation and Operating Manual (INSOP). 

7.  Maintenance 

Only Thommen Aircraft Equipment AG are authorised to perform maintenance tasks not given 

in this manual. 

8.  Warranty 

The warranty for the Stratotimer ST3 is for 24 months. 

9.  Document/Equipment Feedback 

The Document / Equipment Defect Report (on the next page) gives the customer a way to inform 

Thommen Aircraft Equipment AG about any defects regarding the equipment or discrepancies 

in the technical documentation. This feedback will help Thommen Aircraft Equipment AG to make 

continued improvements to the equipment and/or the technical documentation. 

 

 

Summary of Contents for STRATOTIMER ST3

























































Reviews: