RF RGBW Controller(10 Zones)
Feature
High sensitive & high stable touch color wheel, fast & precise color control.
Enable to control 10 zones separately. Each zone can switch on/off separately.
Changing modes of 10 zones can be synchronized without any confusion.
Model:SR-2806 with SR-1003 series
Product Size
10 changing modes. Enable to stay at any color under situation of color changing modes.
Brief introduction of buttons
Power Supply
12-36VDC
L
N
110V-230VAC
Wiring diagram
Adjustable changing speed with 8 levels, quickest speed is 4S, slowest speed is 256S.
Controlling RGBW or RGBY 4 colors that achieve more selectable colors than traditional RGB control.
To adjust brightness of each color independently that can achieve milions of changing colors
To work with power repeater to expand output unlimitedly.
Parameter
Part No.
Iuput Voltage
Remarks
Current
SR-1003RCW
12-36VDC
Constant voltage
4x(60-180)W
4x5A
Output
SR-1003RCWEA
12-36VDC
Constant voltage
4x(96-288)W
4x8A
Remote
Part No.
Operation Voltage
DIMENSIONS
ø/h (mm)
Operation
Frequency
SR-2806
4.5VDC
43.8x131.6x24.5
434MHz/868MHz
Receiver
SR-1012RCW
12-36VDC
Constant current
4x(4.2-12.6)W
4x350mA
SR-1022RCW
12-36VDC
Constant current
4x(8.4-25.2)W
4x700mA
43.8
131.6
24.5
R
G
B
W
“R”
“W”button and indicator
“G”“B”
Working status indicator, the sender is in dormant status when the indicator is off. The
sender is under working when the indicator is flashing rapidly. If the indicator continues
flashing at the frequency of 1 second, it indicates that the sender batteries low and
needs to replace new batteries.
S-
Speed down when color is changing
S+
Speed up when color is changing
M
Multifunction button, used for selecting, Synchronous or asynchronous mode
B-
Brightness down
B+
Brightness up
Multifunction button, used for turn ON/OFF and white output
1
2
3
4
5
6
7
8
9
10
Figure 1-10 is for selecting receiver’s ID and ID itself to turn ON/OFF
Touch wheel for selecting R/G/B colors
R
G
B
W
S-
S+
M
B-
B+
1
2
3
4
5
6
7
8
9
10
RGB/RGBW
w
h
it
e
SR-1003RCW
RGB/RGBW
w
h
it
e
SR-1003RCW
RGB/RGBW
w
h
it
e
SR-1003RCW
Remarks
RF Wireless
Operation
1. Install battery
Initial using easy RGB(W) remote controller, open the battery cover on the back of the sender, load 3pcs 7 AAA
(1.5V) batteries. Please pay attention to the battery’s negative and positive, otherwise it will fail to work.
2. Receiver learning ID
Initial using easy RGB(W) remote controller must learn the ID of the receiver, the purpose of learning ID code is
to make a certain receiver which can correspond the sender.
The method of Receiver learning ID is as follows: press the ID learning button on the sender,
the ID learning indicator is on, then press one of the number button on the sender, press the
number that you want this receiver to be, E.g. If you want this receiver to be No. 1, please press button
first, then touch the wheel , or you can press any functional button on the sender, such as
etc. to transmit signal to the Sender, after Receiver receives the signal from the sender, the indicator will flash a
few times and then turns off, then receiver ID is activated. If the ID activation is failed at the first time, please
repeat the previous procedures.
1
1
2
3
4
5
6
7
8
9
10
S-
S+
M
B-
B+
Think ahead ESC GmbH I Anzengruberstr. 39 I A-9020 Klagenfurt a. W. I T +43 (0)463 21 09 46 I [email protected] I www.think-ahead.at