Thermokon NOVOS 3, Operating Manual, Page: 9 / 53

Manual NOVOS und thanos EVO
Thermokon Sensortechnik GmbH Seite
9
4.2 Home screen
The display on the home screen of the NOVOS room control units can be parameterized. All icons and notifications
can be de-/activated individually. The set point and actual value can also be overwritten. In order to preserve the
display illumination, it is recommended to either dim or completely switch off the display brightness in standby
mode. To reduce the risk of ablation effects of the screen content, it is recommended to use the screen saver. By
default, the screen saver switches on 120 seconds after the last user interaction.
If the room control unit must be
protected against unauthorised use, a screen lock can be set up with an unlock code of 4 digits. The screen lock
becomes active when the room control unit switches to standby mode.
4.2.1 Status bar (Header)
In the header of the main screen, various icons can be shown or hidden as needed through a software variable or
user interaction (e.g. occupancy). Communication icons are only linked to an internal logic.
NOVOS 7 NOVOS Touch / thanos EVO

Condensation (Icon ON/OFF)
 Window open (Icon EIN/AUS)

Calibration due (Icon EIN/AUS with logic)
In connection with the calibration countdown, the
icon is automatically displayed after the time until
next calibration has expired. The calibration
countdown must be set so that the icon appears
after specified time. After the countdown has
elapsed and calibration is completed, the
countdown must be reset and the icon switched
off.

BUS communication error (logic)
If no valid BUS communication is detected within
30 seconds, the icon will automatically appear.

USB communication mode (logic)
When the USB connection via the MicroUSB port
on the bottom of the device is active, the icon
automatically appears.
 Room occupancy - occupied/unoccupied
Description see “ECO function”.

ECO function
(Icon ON/OFF or user interaction)
The room occupancy and ECO function are
triggered on the device via toggle button.
NOVOS 7: Depending on the configuration,
switching to ECO mode is conducted either in the
respective submenu (carousel), in the
temperature menu or through a favorite button.
NOVOS Touch/thanos EVO: Select ECO in the
temperature menu or - if configured - also via a
favorite key.

Heating mode(Icon ON/OFF)
The icons “heating” and “cooling” can also be
displayed in color (heating = red / cooling = blue).
For this purpose, the corresponding parameter
must be set in the display settings. The set point in
the center of the home screen is then displayed in
the same color as the setting.
 Cooling mode (Icon ON/OFF)
For additional settings, see "Heating mode".

PIR active (Icon ON/OFF)
 Warning (Icon ON/OFF)

Maintenance due
In connection with the maintenance countdown,
the icon is automatically displayed after the
maintenance countdown has elapsed. In order to
have the icon appear, the maintenance interval
must be set. After the countdown has expired and
maintenance has been conducted, the countdown
must be reset and the icon should be switched off
again.
Coil data block „Display“ (Icons)
▪
Condensation
▫
Coil 16
On = 1 | Off = 0
▪
Window open
▫
Coil 17
On = 1 | Off = 0
▪
Calibration due
▫ Coil 18
On = 1 | Off = 0
▪
Communiaction error
▪
USB Communication mode active
▪
Heating mode
▫
Coil 22
On = 1 | Off = 0
▪
Cooling mode
▫
Coil 23
On = 1 | Off = 0
▪
PIR
▫
Coil 24
On = 1 | Off = 0
▪
Warning
▫
Coil 26
On = 1 | Off = 0
▪
Maintenance due
▫
Coil 27
On = 1 | Off = 0
Data block „Room climate“
▪
Room occupancy
▫
Data address 100
unoccupied = 0 | occupied = 1
▪
ECO function
▫
Data address 101
ECO not active = 0 | ECO active = 1
Configuration data block „Display“
Display icons and heating/cooling set point
in color (red/blue)
▫
Data address 1212
On = 1 | Off = 0
Configuration data block „General“
▪ Kalibrierungscountdown; Adresse 1114
▪ Kalibrierungsintervall: Adresse 1116
▪ Wartungscountdown; Adresse 1113
▪ Wartungsintervall; Adresse 1115