Thermo NanoDrop One User Manual Download Page 309

Page: 309 / 312

Thermo Scientific

NanoDrop One User Guide

311

About this Help System

Conventions Used

Safety precautions and other important information use the following format:

Trademark Information

DYMO and LabelWriter are either trademarks or registered trademarks of Newell
Rubbermaid in the United States and/or other countries.

Wi-Fi is either a trademark or a registered trademark of Wi-Fi Alliance in the United States
and/or other countries.

Bluetooth is either a trademark or a registered trademark of Bluetooth Special Interest Group.

Windows is either a trademark or a registered trademark of Microsoft Corporation in the
United States and/or other countries.

All other trademarks are the property of Thermo Fisher Scientific inc. and its subsidiaries.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor or

moderate injury.

NOTICE

Follow instructions with this label to avoid damaging the system hardware or

losing data.

Note

Contains helpful supplementary information.

Tip

Provides helpful information that can make a task easier.

Summary of Contents for NanoDrop One
























































































































































































































































































































Search results

Summary of Contents for NanoDrop One

Reviews:

Thermo NanoDrop One, User Manual, Page: 309 / 312

Search results

Summary of Contents for NanoDrop One

Reviews: