manualshive.com logo in svg

Thermo NanoDrop One, User Manual, Page: 301 / 312

Share
Download
Thermo NanoDrop One User Manual Download Page 301

Thermo Scientific

NanoDrop One User Guide

303

Safety Information

Before operating a NanoDrop One instrument, please read the safety information and follow 
its recommendations for the system.

Safety and Special Notices

In many cases, safety information is displayed on the instrument itself. The symbol indicates 
that there is additional safety information in the documentation and failure to heed the safety 
precautions could result in injury.

WARNING  

Indicates a hazardous situation which, if not avoided, could result in death or 

serious injury.

CAUTION  

Indicates a hazardous situation which, if not avoided, could result in minor or 

moderate injury.

NOTICE    

Follow instructions with this label to avoid damaging the system hardware or 

losing data.

Note  

Contains helpful supplementary information.

Summary of Contents for NanoDrop One

























































































































































































































































































































Reviews:

No comments