Thermo NanoDrop One User Manual Download Page 200

Page: 200 / 312

Learning Center

Measure a Sample Using a Cuvette

200

NanoDrop One User Guide

Thermo Scientific

Measure a Sample Using a Cuvette

The NanoDrop One

spectrophotometer includes a

cuvette holder for measuring dilute samples, colorimetric
assays, cell cultures and kinetic studies. The cuvette system
offers an extended lower

detection limit

and an optional

37 °C heater and micro-stirrer.

Supplies needed

• NanoDrop One

spectrophotometer

• lint-free laboratory wipes

• two

compatible cuvettes

• sample material resuspended in appropriate buffer

solution (see

Preparing Samples

)

• pure buffer solution for blanking instrument (see

Choosing and Measuring a Blank

or watch multimedia

training

What is a blank?

)

Summary of Contents for NanoDrop One
























































































































































































































































































































Search results

Summary of Contents for NanoDrop One

Reviews:

Thermo NanoDrop One, User Manual, Page: 200 / 312

Search results

Summary of Contents for NanoDrop One

Reviews: