manualshive.com logo in svg

Thermo Scientific Vanquish VH-P10-A-02, Operating Manual

The Thermo Scientific Vanquish VH-P10-A-02 is an advanced scientific instrument designed for precise analysis. Maximize your productivity with this cutting-edge product by referring to the comprehensive Operating Manual. Downloadable for free from our website, it provides detailed instructions and information to ensure optimal performance and accurate results.

Share
Download
background image

5   

•

 

  Installation 

Page 62 

Vanquish Pumps (VH-P10-A-02) Operating Manual 

5.6.3

 

Connecting Fittings, Capillaries, and Tubing 

This section provides information about how to connect and handle 
capillaries, fittings, and tubing. 

5.6.3.1

 

General Guidelines 

When connecting capillaries and tubing, follow these general 
recommendations: 

•

 

Use only the capillaries and tubing (for example, solvent lines or 
waste tubing) that are shipped with the pump or additional or spare 
capillaries and tubing as recommended by Thermo Fisher Scientific. 

•

 

The connectors must be free from contaminants. Even minute 
particles may cause damage to the system or lead to invalid test 
results. 

•

 

Do not install capillaries or tubes that are stressed, nicked, kinked, or 
otherwise damaged. 

•

 

Install capillaries and fittings only at the positions for which they are 
intended. 

5.6.3.2

 

Connecting Viper Capillaries 

This section describes how to connect Viper™ capillaries. All Viper flow 
connections in the Vanquish system are designed to be finger-tight. 

To connect Viper capillaries with knurl, follow these steps: 

 

NOTICE 

•

 

Tighten or loosen Viper capillaries 

only

 with your fingers. Do not use 

tools other than the knurl that comes with the capillary. 

•

 

To avoid damage to the capillary or connection, tighten and loosen 
the Viper connections 

only

 when the system pressure is down to 

zero. 

 

Summary of Contents for Vanquish VH-P10-A-02















































































































































































































































Reviews:

No comments

Related manuals for Vanquish VH-P10-A-02

Daikin Altherma 3 R F+W Operation Manual preview
Altherma 3 R F+W
Brand: Daikin Pages: 20
EAS Electric ETH220VMA Instruction Manual preview
ETH220VMA
Brand: EAS Electric Pages: 165
vacuubrand NT Series Instructions For Use Manual preview
NT Series
Brand: vacuubrand Pages: 44
EarthLinked PW1 Installation Manual preview
PW1
Brand: EarthLinked Pages: 6
RBI DOMINATOR Series Installation And Operation Manual preview
DOMINATOR Series
Brand: RBI Pages: 52
TATRA PC-10 Installation And Operation Manual preview
PC-10
Brand: TATRA Pages: 16
RBI FUTERA II Series Installation & Operating Instructions Manual preview
FUTERA II Series
Brand: RBI Pages: 32
WaterLogic WL900 Service Manual preview
WL900
Brand: WaterLogic Pages: 29
Clarke 7120400 Operation & Maintenance Instructions Manual preview
7120400
Brand: Clarke Pages: 16
DAXOM UKDAX-10KSM Installation And Operating Manual preview
UKDAX-10KSM
Brand: DAXOM Pages: 20
samhydraulik H1V 2EM Operator'S Manual preview
H1V 2EM
Brand: samhydraulik Pages: 7
Aqua Comfort ACT Signature Series Calibrations And Settings preview
ACT Signature Series
Brand: Aqua Comfort Pages: 2
TapFlo LPX Series Iom Manual preview
LPX Series
Brand: TapFlo Pages: 69
Mallory 4060FI Installation Instructions preview
4060FI
Brand: Mallory Pages: 4
vacuubrand MD 1 Instructions For Use Manual preview
MD 1
Brand: vacuubrand Pages: 72
DAB NKVE MCE Series Instruction For Installation And Maintenance preview
NKVE MCE Series
Brand: DAB Pages: 72
DLS FlexxPump 250 OLED User Manual preview
FlexxPump 250 OLED
Brand: DLS Pages: 80
GSW POWER VENTED GAS FIRED WATER HEATER Installation And Operating Instructions Manual preview
POWER VENTED GAS FIRED WATER HEATER
Brand: GSW Pages: 39

Brands by name

Popular brands

Load more brands