manualshive.com logo in svg

Thermo Scientific Vanquish VH-P10-A-02, Operating Manual

Share
Download
Thermo Scientific Vanquish VH-P10-A-02 Operating Manual Download Page 32

3   

•

 

  Pump Overview 

Page 32 

Vanquish Pumps (VH-P10-A-02) Operating Manual 

3.1

 

Pump Features 

The pump includes the following main features: 

•

 

Two-channel pump with each channel based on a dual-piston in-
parallel design 

•

 

Independent drive for each piston for high accuracy and increased 
flexibility 

•

 

Advanced Thermal Effect Compensation (ATEC) and electronic 
compressibility compensation (SmartFlow™) for precise and virtually 
pulse-free flow 

•

 

Active piston seal wash system for high lifetime of pistons and piston 
seals 
The piston seal wash system keeps the pistons wet and rinses the 
piston seals automatically. This prevents crystallization and particle 
deposits on the piston surfaces and seals, which may damage the 
components. 

•

 

Solvent selector "2 from 6" for increased flexibility 

•

 

Purge unit for easy and automatic purging 

•

 

Built-in vacuum degasser for enhanced flow stability and best 
detector sensitivity 

•

 

Easy access to the user-serviceable components and tool-free 
maintenance procedures for fast and reliable maintenance 

•

 

Easy maintenance because the pump remains in the Vanquish 
system stack 

For specifications, see 

section 9.1 Performance Specifications, page 216

. 

Summary of Contents for Vanquish VH-P10-A-02















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands