manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Instruction Manual

Share
Download
Thermo Scientific TZ-32 Zonal Rotor Instruction Manual Download Page 44

Thermo Scientific TZ-32 Zonal Rotor

 Cleaning of Rotor and Septa — 44

 

6. 4. 

Handling of Rulon Seal and Renewal

Rulon seal is a soft plastic with excellent lubrication developed by mixing tetrafluoroethylene resin with a special filler, and 

is easily scratched by a fingernail. Do not scratch the upper surface, or solution may leak due to poor sealing.

• 

Renewal of Rulon seal

Slightly scratched or worn Rulon seal can be reconditioned by polishing. The flat portion of the zonal rotor cover can 

used for polishing the Rulon seal. Some technique is required for finishing.

Put fine sandpaper (No. 800 is recommendable) on a rotor cover, and polish the contact surface until it becomes 

even.

Do this carefully while removing polishing agent from the Rulon seal surface and sandpaper. Finish it after making 

sure no scratch due to the sandpaper remains on the Rulon seal surface.

• 

Removal of Rulon seal

The Rulon seal can be washed and sterilized together with the shaft. Remove the Rulon seal if the Rulon seal is 

scratched. Be careful not to scratch the Rulon seal surface.

Removing procedure

a.  Insert the accessory extractor into two holes.

b.  Turn it clockwise and counterclockwise while lightly depressing it.

c.  Carefully pull it upwards while turning.

Before resetting it, apply a thin coat of vacuum grease to the O-ring and insert it carefully with soft portions 

of applied fingers.

Figure 41

Polishing the Rulon 
seal

Figure 42

Removal of the 
Rulon seal

Summary of Contents for TZ-32 Zonal Rotor





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands