manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Instruction Manual

Share
Download
Thermo Scientific TZ-32 Zonal Rotor Instruction Manual Download Page 21

Thermo Scientific TZ-32 Zonal Rotor

 Rotor Assembly — 21

 

CAUTION

Do not use the following substances with Noryl

Benzene

Fluorine

Petroleum ether

Carbon tetrachloride

Freon

Polypropylene glycol

Chlorine

Furfural

Pyridine

Chloroform

Heptane

Pyridine sulfate

Dibutyl phthalate

Hexanol

Toluene (toluol)

Ethylene glycol

Kerosene

The following substances may be used with Noryl at 26 °C or below

Acetone

Copper sulfate

Mineral oil

Acetic acid

Cyclohexane

Phenol

Arsenic acid

Ethyl acetate

Potassium bichromate

Alcohol

Ethyl chloride

Potassium carbonate

Alkalies

Ferric chloride

Potassium chlorate

Ammonium chloride

Formic acid

Potassium chloride

Ammonium hydroxide

Hydrobromic acid

Potassium hydroxide

Ammonium phosphate

Hydrochloric acid

Potassium nitrate

Ammonium sulfate

Lactic acid

Potassium sulfate

Amyl acetate

Nitric acid

Sodium bicarbonate

Amyl alcohol

Ortho-phosphoric acid

Sodium bisulfate

Borax

Picric acid

Sodium carbonate

Bromine

Phosphoric acid

Sodium chlorate

Butyl alcohol

Stearic acid

Sodium cyanide

Butyl cellosolve

Sulfuric acid

Sodium hydroxide

Butyl mercaptan

Ferrous sulfate

Sodium nitrate

Benzoic acid

Formaldehyde

Sodium perborate

Boric acid

Glycerin, glycerol

Sodium peroxide

Butyric acid

Hydrogen peroxide

Sodium phosphate

Calcium chloride

Iodine

Sodium pyrophosphate

Calcium hydroxide

Isopropanol

Sodium silicate

Carbon bisulfide

Lead acetate

Sodium sulfate

Cesium chloride

Lithium chloride

Sodium sulfite

Chloracetic acid

Magnesium chloride

Sodium thiosulfate

Chlorosulfonic acid

Magnesium hydroxide

Stannous chloride

Citric acid

Methanol

Sucrose

Copper chloride

Methyl cyclopentane

Tetranitromethane

Copper nitrate

Table 5

Chemical 
Resistance of Noryl

Summary of Contents for TZ-32 Zonal Rotor





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands