manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Instruction Manual

Share
Download
Thermo Scientific TZ-32 Zonal Rotor Instruction Manual Download Page 18

Thermo Scientific TZ-32 Zonal Rotor

 Rotor Assembly — 18

 

4. 2. 10.  Guard plate assembly

The center case supports the seal assembly and maintains the contact between the body and the Rulon seal for injecting 

solution into and extracting it, from the spinning rotor. It is mounted by using the three supports leading from the rotor 

chamber of the centrifuge. It is made of a transparent acryl resin plate for the spinning rotor to be visible. It also prevents 

tools, etc. from dropping into the rotor chamber while it is spinning.

➀

➀

Case

4. 2. 11.  Shield plate

It is mounted on top of the rotor chamber to suppress frosting in the chamber when injecting gradient solution or samples 

into or extracting them from the rotor which is being cooled.

Since the shield plate is also made of a transparent acrylic resin plate, the rotor chamber is clearly visible through this 

plate.

A tube setter is provided for retaining the tubes projecting from the seal assembly. Since the shield plate is divided into 

two semicircular portions, it is easily mountable or removable.

➀

➀

Tube setter

Figure 11

Guard plate 
assembly

Figure 12

Shield plate

Summary of Contents for TZ-32 Zonal Rotor





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands