manualshive.com logo in svg

Thermo Scientific TZ-32 Zonal Rotor, Instruction Manual

Share
Download
Thermo Scientific TZ-32 Zonal Rotor Instruction Manual Download Page 14

Thermo Scientific TZ-32 Zonal Rotor

 Rotor Assembly — 14

 

4.   Assembly

4. 1. 

Rotor Assembly

The rotor is composed of a rotor body, cover, septa, shaft, cap assembly and Rulon

™

 seal attached to the shaft. The TZ-32 

rotor has a capacity of 1690 ml.

4. 1. 3.  Rotor body and cover

The rotor body and cover of the TZ-32 rotor use, as material, titanium alloy of an excellent corrosion resistance. The seal 

packing is fluorine rubber. The metal ring is titanium alloy.

➀

➁

➂

➀

Cap assembly

➁

Cover

➂

Rotor body

4. 1. 4.  Septa

The septa has four vanes that divide the bowl into four sector-shaped compartments, each vane containing a channel to 

carry fluid to the outer edge of the rotor bowl. The solution injected through the seal assembly is led to the outer edge of 

the rotor from the four holes located outside the Rulon seal through the shaft. The septa has slanting surfaces, the top of 

each being provided with a hole communicating from the center of the seal assembly with the hole in the center of the 

Rulon seal. Otherwise, the septa is made of a plastic (Noryl) for which the chemical resistance, cautions in spinning, and 

the maintenance will be described later.

Figure 5

Rotor body and 
cover

Figure 6

Septa

Summary of Contents for TZ-32 Zonal Rotor





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands