manualshive.com logo in svg

Thermo Scientific SOLA II Flare, User Manual

Share
Download
Thermo Scientific SOLA II Flare User Manual Download Page 40

Chapter 3 

Start-Up & Shutdown 

Thermo Scientific 

SOLA II Flare User Manual 

3-4 

Maintenance 

Shutdown 

The analyzer system must be fully shut down and the sample system 
decontaminated as appropriate prior to performing maintenance. Follow this 
procedure when shutting down the analyzer for maintenance or a long-term 
outage. 

1.

 

Close the sample flow to the instrument and purge the sample from the 
unit using nitrogen. 

2.

 

Turn off power to the analyzer. 

3.

 

Allow the instrument to cool. 

Caution

 Failure to allow adequate cooling time before opening the oven can 

lead to equipment damage or injury to personnel. 

▲

 

4.

 

Turn off all air supplies. 

Caution

 Parts of the instrument may be hot even after power is removed. Allow 

the system to cool completely before performing maintenance. 

▲

 

 

Emergency Shutdown 

1.

 

Close the sample supply to the system. 

2.

 

Turn off the main power to the system. 

 

 

 

Summary of Contents for SOLA II Flare





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands