manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 70

13

  Basic Concentration Measurements—Basic A-%T-C

Measuring Samples

60

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

5. Press 

Enter Factor

 to accept the factor and return to the screen displaying the factor and 

units. 

6. Press 

Select Units

.

7. Highlight the appropriate unit in the list and press 

Enter

. 

8. Press 

Esc

 to return to the Conc With Factor screen.

Measuring Samples

If the 6-Position Cell Changer is installed, place the sample you want to measure in one of the 
cell positions and press the corresponding cell position button to move the cell changer to the 
measuring position.

The measurement appears.

If the Single Cell Changer is installed, remove the blank and place the sample in the cell 
changer. The measurement appears.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands