manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 62

11

  Abs and %T Measurements—Basic A-%T-C 

Setting the Wavelength

52

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Setting the Wavelength

To set the wavelength

1. Press 

Set nm

 or any number key to set the wavelength.

2. Enter the wavelength for taking measurements and press 

Set nm

 again.

Measuring a Blank

To measure a blank

1. Place the blank in the cell holder.

If a 6-Position Cell Changer is installed, place the blank in the B position.

2. To enter an absorbance or transmittance value for the blank, press a number key and enter 

the desired value in the 

Entry

 field.

3. Press 

Measure Blank

. 

Measuring Samples

If a 6-Position Cell Changer is installed, place the samples in the cell positions and press the 
corresponding cell position button to move the cell holder to the measuring position. The 
absorbance (ABS) or percent transmittance (%T) measurement appears on the display.

If a Single Cell Holder is installed, remove the blank and place the sample in the cell holder. 
The absorbance or %Transmittance measurement appears on the display.

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands