manualshive.com logo in svg

Thermo Scientific Orion AquaMate 7000 Vis, User Manual

Share
Download
Thermo Scientific Orion AquaMate 7000 Vis User Manual Download Page 130

23

 Maintenance

Routine Care

120

Orion AquaMate 7000 Vis and Orion AquaMate 8000 UV-Vis

Thermo Scientific

Cleaning and Maintaining Cells

Carefully check the condition of the cuvettes and other cells used to measure samples. If they 
are chipped, cracked or scratched, it is important to discard the damaged cell(s) and replace 
them with new ones.

Ensuring your cuvettes are clean both inside and out is important to the quality of your results 
for two reasons: 1) contaminating material may absorb light resulting in falsely high 
absorbance readings; and 2) contaminants in the cell may react chemically with subsequent 
reagents or standards introduced into the cell.

Cleaning methods depend to some extent on the nature of the contaminating material. It is 
important to identify the residual material in the cell that needs to be removed. Refer to the 
following table for suggestions on cleaning methods, solvents and material.

Solvents

Examples

Suggested Cleaning Methods

Aqueous

Protein, Biologics, DNA

• Warm water with detergent

• Dilute  nitric  acid (<10%) rinse

• Copious  water  rinse

Aqueous

Salt solutions

• Dilute nitric acid (<10%) rinse

• Copious  water  rinse

Aqueous

Basic solutions

• Warm water with detergent

• Dilute  nitric  acid (<10%) rinse

• Copious  water  rinse

Organic

Hydrocarbons, small molecules, oils

• Rinse with organic solvent

• Warm water with detergent

• Dilute  nitric  acid (<10%) rinse

• Copious  water  rinse

Organic

Alcohol solutions

• Rinse with similar alcohol, 

acetone, or other solvent

• Copious  water  rinse

Summary of Contents for Orion AquaMate 7000 Vis





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands