Thermo Scientific NanoDrop OneC User Manual Download | Manualshive

Page: 21 / 144

background image

3

Applications

Measure UV-Vis

Thermo Scientific

NanoDrop One

C

with NanoDropQC Software User Guide

17

Settings for UV-Vis Measurements

To show the UV-Vis settings, from the Home screen, select

UV-Vis

.

Setting

Available Options

Description

Monitored
wavelengths

Enter up to 40
wavelengths between
190 nm and 850 nm

User-defined wavelengths to be measured and reported at run
time

. Absorbance values for the first three entered wavelengths

are displayed in the

screen. To see absorbance

values for 8 monitored wavelengths, swipe left in the
measurement screen to show the

. To see all monitored

wavelengths, press and hold a sample row to show the

screen (scroll up to display absorbance values for any

additional user-defined wavelengths).

Note

: If Baseline Correction is selected, all displayed absorbance

values are the corrected values.

Analytical Wavelength

Any wavelength between
190 nm and 850 nm

This is the wavelength the software will use to determine the
pathlength selection.

Automated Pathlength On or Off

(affects pedestal
measurements only)

Optional automated pathlength selection

. Allows the software

to use the optimal (shorter) pedestal pathlength for high
concentration samples to help prevent detector saturation (see

Detection Limits

• When selected, the shorter pathlength is used when any

wavelength between 220 nm and 850 nm has 10 mm
equivalent absorbance value of 12.5 or higher. For
wavelengths between 190 nm and 219 nm the change to the
shorter pathlength occurs when any wavelength in this range
has a 10 mm equivalent absorbance value of 10 or higher.

• When deselected, the pedestal pathlength is restricted to

10 mm across all wavelengths.

Note

: In either case, displayed absorbance values have been

normalized to a 10 mm pathlength equivalent.

Baseline Correction

On or off

Enter baseline correction
wavelength in nm or use
default value (750 nm)

Optional user-defined baseline correction

. Can be used to

correct for any offset caused by light scattering particulates by
subtracting measured absorbance at specified baseline correction
wavelength from absorbance values at all wavelengths in sample
spectrum. As a result, absorbance of sample spectrum is zero at
specified baseline correction wavelength.

«
...
19
20
21
22
23
...
»

Summary of Contents for NanoDrop OneC

















































































































































Reviews:

No comments

Related manuals for NanoDrop OneC

Brand: PAT Pages: 55

Brand: PAT Pages: 31

Brand: Hammond Pages: 130

SourceMeter 2400

Brand: Keithley Pages: 594

System SourceMeter 2601B

Brand: Keithley Pages: 864

Brand: Labgear Pages: 8

SourceMeter 2600B Series

Brand: Keithley Pages: 897

Brand: Waterproof Pages: 10

Brand: Ocean Optics Pages: 43

Brand: Ocean Technology Systems Pages: 12

Brand: Ocean Reef Pages: 24

Brand: palintest Pages: 14

Brand: WATERGUARD Pages: 2

Brand: Gearx Pages: 19

Brand: Schneeberger Pages: 35

BUCKMASTERS 1500

Brand: Sig Sauer Pages: 2

Brand: LaserLine Pages: 11

Brand: LaserLiner Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands