Thermo Scientific KingFisher Flex Service Manual Download Page 164

Page: 164 / 228

7-10

Software

Version 1.1

Service Manual

Thermo Fisher Scientific

KingFisher

Flex

MOR END uc_status

Recordable:

Yes

Example:

MOR 2

MOR

MOR END 0

7.1.11.9 MOS -move shield

This command moves the tip shield to given position. The position is given as on/off

Command:

MOS si_pos ui_speed

si_pos

Position 0 means off and 1 means on.

Range 0 / 1.

ui_speed

Top speed in halfstep/s. Range 20..2000. The default after startup

is 2000.

Only the

ui_pos

parameter is required. Speed defaults to the last one used.

Response:

MOS

MOS END uc_status

Recordable:

Yes

Example:

MOS 1

MOS

MOS END 0

7.1.11.10 PAU -pause for user intervention

This command starts a pause until the Start key is pressed.

Command:

PAU a_text

a_text

Text string to display. See

TXT

command.

Response:

PAU

PAU END uc_status

Recordable:

Yes

The Stop key is also accepted during pause. If the instrument is in COMPUTER CONTROL, it
returns to stand alone mode.

Summary of Contents for KingFisher Flex





































































































































































































































Search results

Summary of Contents for KingFisher Flex

Reviews:

Related manuals for KingFisher Flex

Brands by name

Popular brands

Thermo Scientific KingFisher Flex, Service Manual

Search results

Summary of Contents for KingFisher Flex

Reviews:

Related manuals for KingFisher Flex

Brands by name

Popular brands