Thermo Scientific ISQ 7000 Hardware Manual Download Page 312

Page: 312 / 442

Advanced Maintenance

Replacing Components of the Front Door

284

ISQ 7000 Hardware Manual

Thermo Scientific

Front Door Hinges and Supports



To replace the hinges and supports that connect the front door to the chassis

1. Shut down your system by following the steps in

“Shutting Down the ISQ 7000 System”

page 149

2. Use a T20 Torxhead screwdriver to loosen the left side panel screw from the interior front

panel.

3. Slide the left side panel toward the back of the instrument and lift it off.

4. Look through the left side of the instrument and remove the nut and grounding washer.

Note

See the

ISQ and TSQ GC-MS Spare Parts Guide

for information about ordering this

component.

Note

You do not have to remove the ion source cartridge or the column or vent the

instrument. If you are using hydrogen as a carrier gas, power off the GC.

Figure 298.

Removing the Nut and Grounding Washer

Grounding Washer

Nut

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 312 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: