Thermo Scientific ISQ 7000 Hardware Manual Download Page 195

Page: 195 / 442

Advanced Maintenance

Replacing Components of the Analyzer

Thermo Scientific

ISQ 7000 Hardware Manual

167

Ion Guide



To replace the ion guide:

1. Shut down your system by following the steps in

“Shutting Down the ISQ 7000 System”

page 149

2. Remove the analyzer tray from the instrument by following the instructions in

“Removing the Analyzer Tray from the ISQ 7000 Instrument”

page 151

3. Remove the ion source cartridge according to

“Ion Source Cartridge”

page 216

4. Remove the wire connecting the quadrupole entrance lens to the source interface board

by unscrewing the terminal with a slotted screwdriver.

5. Remove the screws on each side of the endcaps.

6. Remove the entire quadrupole, as well as the ion guide, from the analyzer tray.

7. Slide the rods and exit endcap off the ion guide and entrance endcap.

Note

See the

ISQ and TSQ GC-MS Spare Parts Guide

for information about ordering this

component.

Figure 135.

Removing the Quadrupole and Ion Guide from the Analyzer Tray

Figure 136.

Separating the Ion Guide from the Quadrupole

Screws

Exit Endcap

Entrance Endcap

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Search results

Summary of Contents for ISQ 7000

Reviews:

Thermo Scientific ISQ 7000, Hardware Manual, Page: 195 / 442

Search results

Summary of Contents for ISQ 7000

Reviews: