manualshive.com logo in svg

Thermo Scientific ISQ 7000, Hardware Manual, Page: 161 / 442

Share
Download
Thermo Scientific ISQ 7000 Hardware Manual Download Page 161

 

2 

Troubleshooting

Investigating Vacuum Issues

Thermo Scientific

ISQ 7000 Hardware Manual

133

Investigating Vacuum Issues

When you run Vacuum System Check diagnostics on the ISQ 7000 system, the software 
checks the vacuum system. Vacuum issues may also be found when you run Leak Check 
diagnostics. Your instrument or software may indicate the following types of issues.

WARNING  ELECTRICAL SHOCK HAZARD: 

 When troubleshooting any issue that requires 

removing a cover on the ISQ 7000 mass spectrometer, you should power-off and vent the 
instrument to avoid harming yourself.

AVERTISSEMENT RISQUE D’ÉLECTROCUTION

:  lorsque vous cherchez à résoudre un 

problème nécessitant d’enlever le couvercle du spectromètre de masse ISQ 7000, mettez 
hors tension et ventilez l’instrument pour éviter de vous blesser.

Summary of Contents for ISQ 7000



























































































































































































































































































































































































































































Reviews:

No comments