Thermo Scientific Ion Torrent A45727 User Manual Download Page 57

Page: 57 / 163

In the Setup step, enter or make the following selections.

In Run Plan Name, enter a unique name.

(Optional) In the Reporting (Optional) section, select one or more options if

needed. You can select both options, or leave both options deselected.

Reporting option

Description

Generate Report

Select this option to generate a Lab Report using a

report template that you specify in the list.
To create a report template, click (Assays)

Manage Presets, then in the Report Templates

tab, click Add New.

Upload BAM files to Ion

Reporter

™

Software

Select this option to upload data for further analysis

with Ion Reporter

™

Software.

Select your Ion Reporter

™

Software account and

release version.
To configure an Ion Reporter

™

Server account, see

“Configure an Ion Reporter

™

Server account

(administrator)“ on page 139.
To configure an Ion Reporter

™

Software on Connect

account, see “Configure Thermo Fisher (Connect)

accounts (manager/administrator)“ on page 141.

Click Next.
If a chip is installed in the sequencer, the Chip View graphic in the lower

left corner indicates the lanes that are available for sequencing.

Chapter 5

Create and manage run plans

Create a run plan for a sample run

Genexus

™

Integrated Sequencer User Guide

Summary of Contents for Ion Torrent A45727




































































































































































Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands

Thermo Scientific Ion Torrent A45727, User Manual

Search results

Summary of Contents for Ion Torrent A45727

Reviews:

Related manuals for Ion Torrent A45727

Brands by name

Popular brands