background image

1

 Introduction

Contacting Us

4

Evolution One Series Spectrophotometer User Guide

Thermo Scientific

Contacting Us

For U.S. Technical Support, please contact: 

Thermo Fisher Scientific
5225 Verona Road
Madison, WI 53711-4495 U.S.A.
Telephone: 1 800 532 4752
E-mail: [email protected]

 For International Support, please contact:

Thermo Fisher Scientific 
Telephone: +1 608 273 5017
E-mail: [email protected]

E-mailing Data Files

If you have questions about your data, you can send it to us as an archived workbook file 
(*.iwbk). Please send us the appropriate file as an e-mail attachment.

Product Warranty

Warranties herein are for products manufactured by Thermo Fisher Scientific or its 
authorized dealers.

Thermo Fisher Scientific warrants that this product is free from defects in labor and materials 
and shall conform to its product specifications as defined in the product user documentation.

This warranty covers parts (except those specified below) and labor, and applies only to 
equipment which has been installed and operated in accordance with the documentation 
supplied by Thermo Fisher Scientific, and which has been serviced only by authorized 
Thermo Fisher Scientific dealers or service personnel. This warranty does not apply to 
equipment and accessories that have been modified or tampered with in any way, misused, or 
damaged by accident, neglect, or conditions beyond Thermo Fisher Scientific's control.

Note  

Please have the instrument serial number available when you contact us.

Note  

Please do not send exported report files or user-defined workbooks-these do not 

contain the information we need.

Summary of Contents for Evolution One Series











































Reviews: