Thermo Scientific Dionex Easion Operator'S Manual Download Page 9 | Manualshive

Page: 9 / 126

background image

Doc. 155028-01 08/20

1

1 • Introduction

1.1

Overview of the Dionex Easion

The Thermo Scientific

™

Dionex

™

Easion

™

Ion Chromatography System (Dionex

Easion) performs isocratic ion analyses using suppressed conductivity detection.
The Dionex Easion is an integrated ion chromatography system consisting of a
pump, an injection valve, and a conductivity cell. Other system components
(guard column, separator column, and suppressor) are ordered separately.

The Dionex Easion is controlled with a PC (personal computer) running
Windows

®

10 or Windows

®

8.1 operating system and the Thermo Scientific

™

Dionex

™

Chromeleon

™

7 Chromatography Data System (version 7.2.10 MUa and

later). Chromeleon provides complete instrument control, data acquisition, and
data management.

For communication between the Dionex Easion and the PC on which Chromeleon
is installed, the Dionex Easion must be connected to a USB (Universal Serial Bus)
port on either the PC or an external USB hub. For more information, refer to

Thermo Scientific Dionex Easion Ion Chromatography System Installation
Instructions

(Document No. 155032).

NOTE For an introduction to basic ion chromatography

concepts, see

«
...
7
8
9
10
11
...
»

Summary of Contents for Dionex Easion































































































































Reviews:

No comments

Related manuals for Dionex Easion

Brand: A.MENARINI Pages: 2

Brand: Nektar Pages: 3

Brand: Youkey Pages: 86

Brand: p-light Pages: 28

Brand: Panta Safe Light Pages: 2

Brand: Calrec Pages: 70

Brand: QRS Pages: 16

Brand: QMAXZ Lighting Pages: 36

Brand: Vatech Pages: 137

Brand: Vatech Pages: 68

Brand: Varytec Pages: 52

Brand: SAC Pages: 2

Brand: Keithley Pages: 57

Brand: PMK Pages: 24

Brand: SteelFlex Pages: 13

Scanmate-B DGH 8000

Brand: DGH TECHNOLOGY Pages: 53

Brand: Monosem Pages: 104

Brand: Stahls Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands