background image

10  |   Emerald Bluetooth Enabled Wireless Remote Sensors

Compatible Sensors for Smart-Vue Pro Duo / Quatro Data Logger

Emerald Bluetooth Enabled Wireless 
Remote Sensors 

Smart-Vue Pro data loggers are equipped with Bluetooth low 
energy connectivity to use Emerald sensors as wireless 
remote sensors. Emerald sensors can have an integrated 
temperature sensor or an external Pt100 probe. This enables 
you to monitor and manage equipment in hard-to-access 
locations or where it is impractical to connect wired sensors 
to your Smart-Vue Pro data logger.

Wired and wireless remote sensors connected to a 
Smart-Vue Pro data logger offer the same web application 
usage and functionality.

Figure 1. Smart-Vue Pro data logger with Emerald 

Wireless Remote Sensor (Integrated 

Temperature Sensor)

Figure 2. Emerald with external Pt100 sensor 

You can use any combination of wired or wireless remote 
sensors with your Smart-Vue Pro data loggers with up to two 
active wireless remote sensors on Smart-Vue Pro Duo or up 
to four on Smart-Vue Pro Quatro.

For the Smart-Vue Pro data logger to detect your nearby 
Emerald wireless remote sensor, you must first activate 
Bluetooth on the sensor as described below. The Smart-Vue 
Pro data logger cannot discover a wireless remote sensor if it 
is disabled or in standby mode.

Wireless Remote Sensor 

Calibration

It is important to calibrate the sensors on your Smart-Vue Pro 
data loggers to fine-tune the accuracy of readings. The 
calibration procedure for wireless remote sensors is typically 
handled by a qualified metrology laboratory which determines 
precise correction coefficients and loads them directly in the 
Emerald wireless remote sensor’s memory.

CAUTION: 

Emerald Bluetooth sensors must have 

firmware version 2.3.2 or higher to function as 
wireless remote sensors with Smart-Vue Pro data 
loggers as described in this chapter.

CAUTION: 

Calibration parameters are stored 

directly in Emerald sensors to adjust readings for 
maximum accuracy. Calibration parameters 
cannot be edited via the Smart-Vue Pro web 
application. 

Summary of Contents for Differential Pressure Sensor




































Reviews: