Thermo Scientific Cryofuge 5500i GMP Instructions For Use Manual Download Page 49

Page: 49 / 114

Operation

In extreme cases an unsymmetrical

loading of the rotor could release the

imbalance identification.

Imbalance does not only result in noisy

operation but also in a premature wear

of the drive.

Inserting the centrifuge tubes

The rotor has to be loaded symmetrically. When

loading the rotor only partially, you have to ensure

that opposite bore holes always receive tubes of

equal weight (when centrifuging a single sample,

place a centrifuge tube e.g. filled with water).
After placing the tubes, close the rotor lid.

Fixed-angle rotors:

Proper loading

Improper loading

Summary of Contents for Cryofuge 5500i GMP



















































































































Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands

Thermo Scientific Cryofuge 5500i GMP, Instructions For Use Manual

Search results

Summary of Contents for Cryofuge 5500i GMP

Reviews:

Related manuals for Cryofuge 5500i GMP

Brands by name

Popular brands